KM Portal

Isolation of Bacterial Strain for Biodegradation of Fats, Oil and Grease
Research Output | Dar Al-hikmah Library | IIUM Only

Fat, oil and grease (FOG) deposition is one of the major problems that harm the environment and cause dissatisfaction for human. Uncontrolled and un-pre-treated FOG removal from the kitchen could lead to its accumulation in the piping system. Problems include the interference of fat with the aerobic microorganisms that are responsible in treating t

Perception of Muslim Consumers Towards Tax Deduction Through Zakat in Malaysia: an Empirical Investigation on Muslims in Malaysia
Research Output | Dar Al-hikmah Library | IIUM Only

The aim of this study is to explore the factors which are affecting Muslim consumers‟ perception towards tax deduction through zakat in Malaysia. A conceptual framework was drawn based on the literature. Six factors were extracted through principal component analysis and SEM was run to test the hypotheses. This research found that halal-haram asp

Qos Downlink Schedulers in Lte Towards 5g Network
Research Output | Dar Al-hikmah Library | IIUM Only

LTE is expected to be the dominant system used by operators in these years due to its promising solutions for achieving high capacity and data rate. However, LTE packet scheduling and distributing resources among users is still the main challenge due to unfairness and low performance which occur when allocating resources to users. In this paper, th

Smartphone Based Classification System for Indoor Navigation
Research Output | Dar Al-hikmah Library | IIUM Only

This paper introduces a smartphone-based classification system for an indoor environment of a walking person. The system relies only on smartphone inertial data and it can be considered as a smartphone-based aiding system for an indoor navigation. In addition, it does not need pre-installing of wireless network in the environment or heavily tuning

Multi Objective Optimisation for High Speed End Milling Using Simulated Annealing Algorithm
Research Output | Dar Al-hikmah Library | IIUM Only

Machining at high cutting speeds produces higher temperatures in the cutting zone. These temperatures affect the surface quality and flank wear progress. Therefore, determining the optimum cutting levels to achieve the minimum surface roughness and flank wear is an important for it is economical and mechanical issues. This paper presents the optimi

Using the Desirability Function as an Effective Tool in Target Costing Model
Research Output | Dar Al-hikmah Library | IIUM Only

High speed turning (HST) is an advanced machining process that uses higher cutting speeds than those used in conventional machining. HST enables manufacturers to shorten machining times. Therefore, this approach should be followed and justified by economic study. One of the most effective tools for economic study is by developing a target-cost mode

Surface Roughness Prediction in High Speed End Milling Using Adaptive neuro-Fuzzy Inference System
Research Output | Dar Al-hikmah Library | IIUM Only

One of the significant characteristics in machining process is final quality of surface. The best measurement for this quality is the surface roughness. Therefore, estimating the surface roughness before the machining is a serious matter. The aim of this research is to estimate and simulate the average surface roughness (Ra) in high speed end milli

Energy Cost Optimization in High Speed Hard Turning Using Simulated Annealing Algorithm
Research Output | Dar Al-hikmah Library | IIUM Only

Selecting the cutting conditions to optimize the economics of machining process as assessed by energy machining cost is essential. The aim of this research is to determine the optimum cutting parameters that minimize the energy cost needed for removing one cubic centimetre of material in High Speed Hard Turning (HSHT) process. To achieve that, a se

Evaluation of Workload and its Impact on Satisfaction Among Pharmacy Academicians in Southern India
Research Output | Dar Al-hikmah Library | IIUM Only

Objective: The purpose of this study was to determine the level of workload among pharmacy academicians working in public and private sector universities in India. The study also aimed to assess the satisfaction of academicians towards their workload. Materials and Methods: A cross-sectional study was conducted for a period of 2 months among pharma

A New Efficient Text Detection Method for Image Spam Filtering
Research Output | Dar Al-hikmah Library | IIUM Only

Detection of text in images plays an important role in many situations such as video retrieval, annotation, indexing, and content analysis. In information security to filter image spam, one main feature can be used is text contents in image. Extracting text features from image spam needs efficient text detection. Obfuscating techniques used by spam

Category

KCDIOM

Type

KCDIOM

KM Portal