KM Portal

Engineering Students’ Perceptions and Acceptance of the Online Flipped Classroom for Learning During the Covid-19 Pandemic
Research Output | Dar Al-hikmah Library | IIUM Only

This article reports on the results of an open-response survey sent out to IIUM Engineering students to elicit their thoughts and views about learning their courses online via the flipped learning mode. The decision to take academic courses online was brought about by the COVID-19 pandemic which has forced many sectors, including the education sect

KOE e-Learning Assessment Sop V01
Research Output | Dar Al-hikmah Library | IIUM Only

This guideline is prepared for the Kulliyyah of Engineering lecturers on behalf of the kulliyyah’s e-learning teaching and learning committee.KOE e-Learning Assessment SOP v01 Prepared by: Dr, Nor Fadhillah Binti Mohamed Azmin Dr. Afifah Binti Mohd Ali Dr. Adib Hamdani Bin Rosli Dr. Syazwani Binti Mohd Zaki Purpose 2The purpose of this guideline

Noble Tool Based Micromilling for Nanometric Surface Finish
Research Output | Dar Al-hikmah Library | IIUM Only

This research introduced micro electro discharge (ED) milling as a potential technique to fabricate miniaturized components. It investigated the influence of three micro ED milling process parameters, which were feed rate, capacitance and voltage. The response variables were average surface roughness (Ra), maximum peak-to-valley roughness height (R

Powder Mixed Micro Electro Discharge Machining (Pmμedm)
Research Output | Dar Al-hikmah Library | IIUM Only

This paper presents the influence of silicon carbide (SiC) powder concentration and electrical discharge energy in dielectric fluid of micro electro discharge machining (μEDM) of titanium alloy (Ti-6Al-4V) with tungsten carbide (WC) electrode. SiC powder concentration and electrical discharge energy were two input variables. Three responses namely

The Three Abrahamic Faiths and their Roles in Making Peace, Unity and co-Existence Through Moral and Ethical, Religious and socio-Cultural Transformations
Research Output | Dar Al-hikmah Library | IIUM Only

The three Divine Abrahamic faiths i.e. Judaism, Christianity and Islam, revealed to the prophets of God, are divine religions that shape outlook of life, people’s perception, culture and civilization and enhance the relationship between God-man-universe. In this process, people who adhere to a particular religion tend to explore the phenomena thr

Investigation of Tribological Issues in Microforming: a Review
Research Output | Dar Al-hikmah Library | IIUM Only

This paper presents the extensive review of microtribology especially as encountered in microforming. Microforming is one of the most frequently used mass production processes by replication. Micro injection moulding, micro deep drawing, micro casting, and hot embossing are the examples of microforming. These processes are suitable for near net sha

Powder Mixed Micro Electro Discharge Milling of Titanium Alloy: Analysis of Surface Roughness
Research Output | Dar Al-hikmah Library | IIUM Only

This paper presents effects of silicon carbide SiC powder concentration on micro EDM parameters on average surface roughness (Ra). The aim is to achieve minimum Ra value on titanium alloy (Ti-6Al-4V) machined with tungsten electrode for various level of concentration of SiC powder and discharge energy (E). By using two-parameter and four-level fact

Fabrication of Silicon Nanopillar Sheet for Cell Culture Dish
Research Output | Dar Al-hikmah Library | IIUM Only

This paper discusses the fabrication of nanopillars using focused ion beam (FIB) sputtering. A 25 keV Ga+ FIB was used to machine the nanopillars. A reversed bitmap method was used to fabricate nanopillars where it milled the substrate all over except the nanopillar area. The height of the nanopillars ranges from 1 to 5.5 μm with aspect ratio of 1

Minimum Chip Thickness in Machining MEMS Structure Using Tool Based Micromilling
Research Output | Dar Al-hikmah Library | IIUM Only

Tool based micromilling is a promising micromanufacturing technology to produce miniaturized features of about 25μm in size frMEMS and Bio-MEMS applications.It is the most flexible and the fastest way to produce complex three dimensional microcomponents including sharp edges with surface finish at a reasonble cost.Moreover,it is capable of machini

Fabrication of Micropillar Sheet for Cell Culture Dish
Research Output | Dar Al-hikmah Library | IIUM Only

Cell culture is one of the major tools in life sciences. Conventionally, cells are placed in a flat petri dish made of glass or plastic. It is used to monitor cells behavior under controlled conditions. As the cells are strongly adhered to petri dish, an additional process of trypsinization is applied to remove the cells from the dish. Alternativel

Category

KCDIOM

Type

KCDIOM

KM Portal