KM Portal

Porous Alumina–hydroxyapatite Composites Through Protein Foaming–consolidation Method
Research Output | Dar Al-hikmah Library | IIUM Only

This report presents physical characterization and cell culture test of porous alumina–hydroxyapatite (HA) composites fabricated through protein foaming–consolidation technique. Alumina and HA powders were mixed with yolk and starch at an adjusted ratio to make slurry. The resulting slip was poured into cylindrical shaped molds and followed by

Floating Porous Alumina from Protein foaming-Consolidation Technique for Cell Culture Application
Research Output | Dar Al-hikmah Library | IIUM Only

Floating porous ceramics have been successfully fabricated using protein foaming-consolidation method. Alumina powder and yolk as the pore creator were mixed while stirring and the resulting slips were poured into cylindrical shaped molds followed by drying for foaming-consolidation process. The dried green bodies were then burned at 600 8C for 1 h

Comparison of Machinability of Ceramic Insert in Room Temperature and Cryogenic Cooling Conditions During End Milling Inconel 718
Research Output | Dar Al-hikmah Library | IIUM Only

Nickel based super alloy or Inconel 718 is known as heat resistant alloys which they are primarily used in gas turbine, steam turbine component and aircraft engine component construction [1]. Inconel 718 attained several unique combinations of properties like strength at elevated temperature, resistance to chemical degradation and wear resistance [

Development of a Mathematical Model for the Prediction of Surface Roughness in End Milling of Stainless Steel Ss 304
Research Output | Dar Al-hikmah Library | IIUM Only

The use of advanced computer-based systems for the selection of optimum conditions of mechanical components during process planning becomes essential for today’s complex products. Computer aided manufacturing (CAM) has widely been implemented to obtain more accurate machining data and to ensure that optimum production is achieved. Machinability o

The Effect of Cryogenic Cooling in Machinability of Stainless Steel During Turning
Research Output | Dar Al-hikmah Library | IIUM Only

A high cutting temperature inherently characterizes high production machining. Such a high cutting temperature adversely effects tool life, dimensional and form accuracy and surface integrity of the product. Currently, an effort is being made to control this problem by reducing heat from the cutting zone through proper selection of machining parame

Elimination of Burr Formation During End Milling of Polymethyl Methacrylate (Pmma) Through High Speed Machining
Research Output | Dar Al-hikmah Library | IIUM Only

A burr is a raised edge or small pieces of material remaining attached to a workpiece after it has undergone machining. The Burr, Edge and Surface Technology (BEST) Division, the Society of Manufacturing Engineers defines a burr as “an undesirable projection of material that results from cutting, forming, blanking or shearing operation [1]. The f

Undergraduate Prospectus.
Knowledge Resources | Dar Al-hikmah Library | Public Access

Subject(s): Glasgow Caledonian University -- Periodicals | Education, Higher -- Periodicals -- Scotland | Universities and colleges -- Periodicals -- Scotland Holdings: ,Official Publication,Gombak Campus Library,Universities & Colleges Publications Collection,,gu uk-st.CALEDONIAN/A24 2002,Available,00000711877

The Hutchinson Dictionary of Ideas
Knowledge Resources | Dar Al-hikmah Library | Public Access

Subject(s): Philosophy -- Dictionaries | Science -- Dictionaries | Religion -- Dictionaries | Political science -- Dictionaries | History -- Dictionaries Holdings: ,Book - Reference,Gombak Campus Library,Reference Collection,,r B41H975H,Not for loan,00000352636

Needs Analysis and the Three Areas of Controversies in Eap
Research Output | Dar Al-hikmah Library | IIUM Only

Juxtaposing needs analysis with rights analysis has been an alternative approach in employing needs analysis in EAP (Benesch, 1999, 2001). On a different note, Hyland (2006) proposes that EAP can be related to three areas of controversies: 1) the two approaches in EAP – EGAP and ESAP; 2) the approaches in the teaching of student writing – the s

Physical Ergonomics in Peripheral Nerve Block
Research Output | Dar Al-hikmah Library | IIUM Only

The understanding of ergonomics is a vital competency for all peripheral nerve block operators. The essence of physical ergonomics for peripheral nerve block procedures can be summarised into three significant components: brain, musculoskeletal and needling. The first component includes strategies to optimise visuospatial neuroprocessing using equi

Category

KCDIOM

Type

KCDIOM

KM Portal